K&G Machinery

  • Home
  • Product
    • Aluminum Camlock Coupling
    • Stainless Steel Camlock Fitting
    • Brass Camlock Coupling
    • Polypropylene Camlock Fittings
    • Nylon Camlock Fitting
    • TW Coupling
    • Guillemin Coupling
    • Geka Coupling
    • LNC Couplings
    • Bauer Coupling
  • About Us
  • News
  • Contact Us
  • Home
  • News
  • Blogs
  • Camlock Gasket Selection: NBR, EPDM, Viton & PTFE

Camlock Gasket Selection: NBR, EPDM, Viton & PTFE

/ Monday, 16 November 2026 / Published in Blogs

By K&G Technical Team  |  Reviewed by K&G Engineering

The gasket is the most common cause of a leaking camlock coupling — and the easiest part to get wrong. A gasket that is the right size but the wrong material can swell, harden or dissolve within days. This guide explains the five common camlock gasket materials, what they are good for, and how to choose one for your fluid.

Where the gasket sits

In a camlock coupling, the gasket sits inside the female coupler. When the male adapter is pushed in and the cam arms are closed, the adapter compresses the gasket against the coupler body to seal the joint. The gasket must match the coupler size — a 2-inch gasket will not seal a 1-1/2-inch coupler — and the fluid, temperature and pressure.

Camlock gasket materials at a glance

Gasket Best for Typical temperature Avoid
NBR (nitrile) Petroleum products, water, air, general oils -20 to 100 °C Ketones, strong acids, ozone
EPDM Water, steam, mild chemicals, outdoor water lines -40 to 120 °C Petroleum oils and fuels
Viton / FKM Fuels, oils, acids, high-temperature service -20 to 200 °C Ketones, low-molecular esters
PTFE Aggressive chemicals, food and pharmaceutical -100 to 260 °C Applications needing high elasticity
Silicone Food, high temperature, dry heat -60 to 200 °C Petroleum oils and fuels

These are typical ranges. For a specific chemical, always confirm compatibility with the gasket manufacturer or with our technical team.

How to choose the right gasket

  1. Identify the fluid. Water, fuel, oil, acid, caustic, solvent, food or steam — each narrows the material choice.
  2. Check the concentration. A diluted acid may be compatible with one material; a concentrated acid may not.
  3. Check the temperature. The gasket must handle the highest continuous temperature, not just the ambient temperature.
  4. Check the pressure. Higher pressure needs a gasket that will not extrude or deform.
  5. Check the standard. Food and pharmaceutical applications may require FDA-compliant or USP Class VI materials.
  6. Confirm the size and profile. Use the gasket designed for your camlock size and type.

Common gasket mistakes

  • Using NBR for everything. NBR is excellent for petroleum and water, but not for ketones or strong acids.
  • Using EPDM with oils. EPDM swells in petroleum-based fluids.
  • Using the wrong size. A loose gasket can fold or extrude; a tight gasket can distort.
  • Reusing a hardened gasket. If the gasket is cracked, flattened or hard, replace it.
  • Ignoring temperature. A gasket that is compatible at room temperature may fail at 120 °C.
  • Missing the gasket entirely. A camlock will not seal without a gasket, even if the arms lock.

Gasket materials and typical applications

NBR for petroleum and water

NBR is the default choice for fuel, diesel, petrol, lubricating oil, water and air. It has good resistance to oils and abrasion, and is cost-effective. Do not use it with ketones, strong acids or ozone.

EPDM for water and steam

EPDM is excellent for water, hot water, steam and many mild chemicals. It is common in outdoor water lines and washdown. It is not suitable for petroleum oils or fuels.

Viton/FKM for fuels and high temperature

Viton is a fluoroelastomer with broad chemical resistance and high-temperature capability. It is a good choice for fuels, oils, acids and high-temperature service, but it is more expensive than NBR or EPDM.

PTFE for aggressive chemicals

PTFE is chemically inert across a wide range of aggressive fluids and has a very wide temperature range. It is less elastic than rubber, so it is used where chemical resistance matters more than flexibility.

Silicone for food and high temperature

Silicone is flexible at low and high temperatures and is often used in food and pharmaceutical applications. It is not suitable for petroleum oils and fuels.

Frequently asked questions

What is the most common camlock gasket material?

NBR is the most common general-purpose gasket for water, petroleum and air. EPDM is common for water and steam; Viton is common for fuels and high temperature.

Can I use an EPDM gasket for diesel?

No. EPDM swells in petroleum-based fuels. Use NBR or Viton for diesel and petrol.

How often should I replace a camlock gasket?

Inspect it at every connection and replace it if it is cracked, hard, swollen or deformed. In continuous service, replace it at the interval recommended by your maintenance plan.

Are all camlock gaskets the same size?

No. Gaskets are size-specific. Use the gasket designed for your nominal camlock size and type.

Not sure which gasket your fluid needs? Send us the fluid, concentration, temperature and pressure and we will recommend a gasket material. For the full type reference, see the camlock coupling type chart.

  • Tweet

What you can read next

Camlock Coupling Types: A, B, C, D, E, F, DC, DP
camlock fittings production line
Camlock Fittings By K&G Machinery
Sanitary Camlock Couplings for Pharmaceutical & Bio-Processing

Product Categories

  • Aluminum Camlock Coupling
  • Stainless Steel Camlock Fitting
  • Brass Camlock Coupling
  • Polypropylene Camlock Fittings
  • Nylon Camlock Fitting
  • TW Coupling
  • Guillemin Coupling
  • Geka Coupling
  • LNC Couplings
  • Bauer Coupling

PRODUCTS

  • Aluminum Camlock Coupling
  • Stainless Steel Camlock Fitting
  • Brass Camlock Coupling
  • Polypropylene Camlock Fittings
  • Nylon Camlock Fitting
  • TW Coupling
  • Guillemin Coupling
  • Geka Coupling
  • LNC Couplings
  • Bauer Coupling

ABOUT US

K&G Machinery is abbreviation of KANGTAI, which a manufacturer of hose fittings(camlock fittings,camlock coupling,storz coupling,reducing coupling), valve and hardware for nearly 30 years.Medium pressure couplings(camlock coupling) for use where quick or frequent connection and disconnection is required. Used mainly for suction and delivery of petroleum products, chemicals, water and other liquid or dry products. Available in aluminium, nyglass, polypropylene, brass and stainless steel.

CONTACT INFO

  • ADD: RM 1820,No.598 Nujiang North Road, Hongxing World Trade Building B, Shanghai,200333,China
  • TEL: +86 21 66630188
  • E-mail: eric@kg-machinery.com
© Copyright2012- 2026. K&G Machinery Co., Ltd. All Rights Reserved.
TOP